ISO extension harness with switch on 80cm extension for manually switching on radio without having the vehicles ignition on. Commonly used on camper vans and motor homes.

Suitable for almost any vehicle with a permanent 12v feed to the radio using standard ISO connections.

Retains the top screen on all Lexus RX (XU30) built between 2004 - 2006 and models built between 2007 - 2008 with navigation.

Retains use of the top screen for both navigation and air con visualisation after an after market radio has been fitted.

Momentary switch to retain and switch between the reverse and side cameras on the top screen of the Nissan Elgrand E51 with CARWINGS.

97mm diameter mounting hole required.

Interface to connect to the CAN ignition of certain cars and trucks from General Motors and provide ignition output as well as interfacing with the steering wheel controls and original amplifier.

This interface also includes subwoofer retention and a reverse signal, speed pulse and parking brake outputs.

Suitable for certain Buick, Cadillac, Chevrolet, GMC, Hummer, Isuzu, Oldsmobile, Pontiac, Saab and Saturn models built between 2000 - 2013, see long description for compatibility.

NOT SUITABLE for retaining steering wheel controls on Chinese/unbranded head units with 2 wire SWC interface (KEY1/KEY2) 

Eliminates ground loop noise between the audio source and radio. Stops alternator "whine" and ignition "ticking".

Used to solve noise problems in Car audio audio systems and AUX in situations.

• For Removing Pops Clicks And Engine Noise When Using Factory AMPS With Aftermarket Radios.
• Secure fit
• Designed with the installer user in mind

PLEASE NOTE: For a bulk pack of 10, please use 24-020B

Bulk pack of 10 RCA Stereo Ground Loop Isolators/ Audio Signal Noise Filters (2 Channel)

Eliminates ground loop noise between the audio source and radio. Stops alternator "whine" and ignition "ticking".

Used to solve noise problems in Car audio audio systems and AUX in situations.

• For Removing Pops Clicks And Engine Noise When Using Factory AMPS With Aftermarket Radios.
• Secure fit
• Designed with the installer user in mind

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface and ISO cables allowing use of original buttons with a new aftermarket head-unit. Includes ISO power to connect the car to the aftermarket head-unit. 

The interface also provides a breakout cable to retain the original top screen for the climate controls

Suitable for Honda Accord (Euro) 2003 - 2009 and Acura TSX 2004 - 2008

PLEASE NOTE: This interface includes PHONE commands for compatible Bluetooth head-units

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface allowing use of original buttons with a new aftermarket head-unit.

This interface also allows vehicle settings and clock adjustment to be displayed on any aftermarket head unit with rear camera input.

Suitable for select Vauxhall, Chevrolet and Holden vehicle models.

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface allowing use of original buttons with a new aftermarket head-unit. 

This interface will also retain vehicle settings and parking sensor information, as well as providing a rear camera input.  

Suitable for Jeep Renegade (2015-2021) car models with original amplified Uconnect systems

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Steering wheel interface allowing use of original buttons with a new aftermarket radio.

This interface allows vehicle settings to be displayed on any aftermarket head unit with rear camera input.

Suitable for select Range Rover Evoque models.

PLEASE NOTE: This is a special product order which we don't stock. Please email our sales team for availability

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface allowing use of original buttons with a new aftermarket head-unit.

This interface also allows vehicle settings and clock adjustment to be displayed on any aftermarket head unit with rear camera input.

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

Car Audio Steering wheel interface allowing use of original buttons with a new aftermarket head-unit.

This interface allows vehicle settings and clock adjustment to be displayed on any aftermarket head unit with rear camera input.

Suitable for Seat Ibiza, Leon and Arona car models

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

This interface allows the use of the Steering Wheel audio controls, select vehicle settings, Optical Parking Sensor Display And Climate Control Visualization when installing an aftermarket head unit.

Suitable for select Volkswagen VW Golf 2012-2018 (Non Amplified) and Polo (2012-2018) car models with MIB Composition Units.

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

This interface allows the use of the Steering Wheel audio controls, Optical Parking Sensor Display And Climate Control Visualization when installing an aftermarket head unit.

Suitable for select Volkswagen vehicle models with original MIB/ PQ radio systems.

PLEASE NOTE: An additional patch lead is required for the steering controls depending on the make of radio being fitted. If unsure please see Full Description

This interface will retain Steering controls and also provide optional input for reversing camera/ parking sensors (if applicable) and outputs for park brake, speed pulse, reverse gear and mute

Suitable for select Volkswagen vehicle models with original MIB II radio systems.

PLEASE NOTE: This interface will only retain basic features such as steering wheel controls on Single DIN radios

Multimedia Steering wheel control interface for various VW cars with select Kenwood models with the EXT/IF (UART) connector.

Includes a pre-wired CANbus interface to provide Ignition, Illumination, Steering controls, Reverse signal, Park Pilot screen retention, Climate control display if in car

This interface is compatible with the older style (48 pin) quadlock connector usually found on previous model variants of some Volkswagen vehicles.

PLEASE NOTE: Only compatible with select Kenwood models with the UART connector. These include Kenwood DMX8020DABS, DNX516DABS and DNX518DABS 

Multimedia Steering wheel control interface for various VW cars with select Kenwood models with the EXT/IF (UART) connector

This interface is compatible with the newer style (52 pi Quadlock connector usually found on 2015 onwards model variants of some Volkswagen vehicles.

Includes a pre-wired CANbus interface to provide Ignition, Illumination, Steering controls, Reverse signal, Park Pilot screen retention, Climate control display if in car

PLEASE NOTE: Only compatible with select Kenwood models with the UART connector. These include Kenwood DMX8020DABS, DNX516DABS and DNX518DABS 

Special adapter lead for the fitting of a Mercedes Audio 20 head unit into a vehicle with an original Audio 5 head unit.

Seat Ibiza (2014-2017) button relocation harness.

This is used to relocate the original hazard and passenger airbag buttons when fitting an aftermarket head unit

Suitable for Seat Ibiza (2014-2017) car models with heated seats only

PLEASE NOTE: A new button panel will need to be used with this harness.

Seat Ibiza (2014-2017) button relocation harness.

This is used to relocate the original hazard and passenger airbag buttons when fitting an aftermarket head unit

Suitable for Seat Ibiza (2014-2017) car models without heated seats

PLEASE NOTE: A new button panel will need to be used with this harness.

Seat Ibiza (2014-2017) button relocation harness.

This is used to relocate the original hazard and passenger airbag buttons when fitting an aftermarket head unit

Suitable for Seat Ibiza (2014-2017) car models with Start/Stop

PLEASE NOTE: A new button panel will need to be used with this harness. The Start/Stop function is lost when the radio is changed.

Multimedia Steering wheel control interface for various VW cars with select Kenwood models with the UART connector.

Includes a pre-wired CANbus interface to provide Ignition, Illumination, Steering controls, Reverse signal, Park Pilot screen retention, Climate control display if in car

This interface is compatible with the older style quadlock connector usually found on previous model variants of some Volkswagen vehicles.

PLEASE NOTE: Only compatible with select Kenwood models with the UART connector. These include Kenwood DMX8020DABS, DNX516DABS and DNX518DABS 

Multimedia Steering wheel control interface for various VW cars with select Kenwood models with the UART connector.

This interface is compatible with the newer style (2 PIN) Quadlock connector usually found on p model variants of some Volkswagen vehicles.

Includes a pre-wired CANbus interface to provide Ignition, Illumination, Steering controls, Reverse signal, Park Pilot screen retention, Climate control display if in car

PLEASE NOTE: Only compatible with select Kenwood models with the UART connector. These include Kenwood DMX8020DABS, DNX516DABS and DNX518DABS 

Multimedia Steering wheel control interface for various VW cars with Pioneer AVIC- navigation models with the UART connector

PLEASE NOTE: Only compatible with Pioneer AVIC models

PDC display and  Steering wheel control interface for various VW cars with Pioneer AVIC- navigation models with the UART connection

PLEASE NOTE: Only compatible with Pioneer AVIC- models

Wiring conversion cable for fitting the Pioneer EVO kit to a Renault Clio 2012-2019 with a OEM Autoradio Smartphone head unit.

This interface comes with a Pioneer patch lead included.

Only for use with the Renault Clio Pioneer EVO kit.

Steering Wheel Interface for fitting the Pioneer EVO kit to a Renault Clio 2012-2016 with a OEM R-Link navigation head unit.

This interface comes with a Pioneer patch lead included.

Only for use with the Renault Clio Pioneer EVO kit.

Replacement button assembly panel for Seat Ibiza cars, to be used when installing a new head unit in 2014-2017 model cars.

Replacement button assembly panel for Seat Ibiza cars, to be used when installing a new head unit in 2014-2017 model cars.

ALL SYMBOLS