Interfaces for adding front and rear camera's to cars OEM system
This power relay cable is to be used when installing a camera into a vehicle.
Sometimes a reverse power feed from a reverse light may not be strong enough to power a camera or may create interference.
This relay can use a weak reverse trigger to switch on a better 12v power feed for a camera or reduce interference.
Requires hardwiring.
Pioneer Dometic conversion kit cable for Camper/ Campervan conversions (Grey Connectors)
Conversion Kit for campers/ campervans which have the dometic video cable pre-installed from factory but wish to use a Pioneer camera and/or head unit.
Compatible with the dometic shadow grey connectors.
Pioneer Part Number: CA-BC-WAE.002
Pioneer Dometic conversion kit cable for Camper/ Campervan conversions (Blue Connectors)
Conversion Kit for campers/ campervans which have the dometic video cable pre-installed from factory but wish to use a Pioneer camera and/or head unit.
Compatible with the dometic water blue connectors.
Pioneer Part Number: CA-BC-WAE.001
8 pin camera adapter cable to allow you to add an aftermarket rear view camera to OEM monitors on various Subaru models from 2008-2015.
Fits cars with original Kenwood navigation or car with the 4.3" screen and navigation
28 pin camera adapter cable to allow you to add an aftermarket rear view camera to OEM monitors MFD GEN5.
Suits Toyota Land Cruiser 200 (07-09) and various Lexus models GS, LS,(07-09) , IS250 and 350 from (06-09)
40 pin camera adapter cable to allow you to add an aftermarket rear view NTSC camera to OEM monitors on Toyota Prius/ Lexus RX models with MFD GEN5 multi-displays.
PLEASE NOTE: Only suitable for NTSC cameras
8 pin camera adapter cable to allow you to add an aftermarket rear view camera to OEM monitors on Toyota/ Citroen and Peugeot cars with X-Touch/ X-Nav systems.
40 pin OEM camera adapter cable to allow you to add an aftermarket rear view camera to Nissan Leaf cars with OEM Nissan EV GEN1 and EV GEN2 multimedia systems.
This 32 pin OEM camera adapter cable to allow you to add an aftermarket rear view camera to Nissan models with Nissan Audio multimedia systems (WITHOUT NAVIGATION)
This cable will allow you to add an aftermarket camera to OEM Honda navigation systems which have a green 7 PIN connection on the back of the head unit .
Suits Honda 2VNO navigation units (with green 7 PIN connection)
Fits Honda models before 2012 with original navigation model 2VN3 and 08A40-3M6-401 type 9953485
Enables you to connect an aftermarket back up camera to the original OEM screen.
24 pin OEM camera adapter cable to allow you to add an aftermarket rear view camera to Honda cars with OEM Honda i-MID 8" and touch screen Monitors.
Reverse Camera input adaptor for Ford SYNC 1 Systems with a 4.2" colour screen. Vehicle Coding required
Enables connection of a aftermarket backup camera to the original OEM SYNC system.
Enables addition of an aftermarket NTSC reversing camera to the original Mazda screen.
Allows you to add an aftermarket camera to the OEM screen on a Mercedes factory fitted head unit.
PLEASE NOTE: This cable is only compatible with single fakra connections. Double fakra connections are not supported. NTSC only
You will need to code the head unit for camera input.
Reverse camera adapter lead for Suzuki cars. Add an aftermarket reverse camera to a Suzuki car with original navigation head units.
Reverse camera adapter lead for Clarion NX504E, NX503E and FX503E head units.
Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Mazda car models (Display and navigation model radios only).
This adapter cable also allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.
PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671
Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Toyota, Scion and Subaru car models (Display and navigation model radios only).
This adapter cable also allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.
PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671
Allows you to retain the original OEM factory fitted camera when installing a new aftermarket head unit on select Toyota, Scion and Subaru car models (Display and navigation model radios only).
PLEASE NOTE: If adding an aftermarket camera to the original system please use part number 27-249
Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Toyota car models with 24 (9+15) Pin connector (Display and navigation model radios only).
This adapter cable also allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.
PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671
Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Toyota (2012 Onwards) car models (Display and navigation model radios only).
This adapter cable also allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.
PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671
Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Hyundai and Kia cars with a factory fitted navigation system.
This adapter cable also allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.
PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671
Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Hyundai and Kia cars without factory fitted navigation systems.
This adapter cable also allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.
PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671
This adapter cable allows you retain the original OEM factory fitted camera when installing a new aftermarket head unit.
Suitable on select Subaru (2015 Onwards) car models with original 6.2 inch basic screen.
PLEASE NOTE: If retaining a camera please purchase this adapter cable with a 12v to 6v voltage converter, part number 10-671
Allows you to add an aftermarket reverse view camera to the original factory fitted head unit on select Nissan (2015 Onwards) cars with a 4.3 inch factory colour display and 32 PIN connection behind the screen.
PLEASE NOTE: Not suitable for Nissan car models with 360 degree Birds Eye view camera systems
Add an aftermarket reverse camera to the original media head unit.
Reverse camera adapter lead for Iveco Daily vans fitted with original IVEConnect media head units.
Adapter to add a reverse view camera to various Renault and Dacia vehicles with MEDIA Nav screen head units.
NOT Suitable for R Link 1 and R Link 2 systems
The camera input may need to be activated by a dealer.
This 28 pin OEM camera adapter cable allows you to add an aftermarket rear view camera to Toyota models with original Toyota Touch 2 systems.
Camera interface cable allowing you to add a reverse Camera to select Mazda (2014 Onwards) car models with factory fit 7 inch MZD Connect Screen based systems.
This cable allows you to add an aftermarket back-up NTSC camera to the Mazda MZD connect original screen
Suitable for various Mazda cars 2014 onwards with original 7" MZD Connect monitor and 28 pin connector.
PLEASE NOTE: Additional programming may be required to activate the rear view camera option on some vehicles
This camera cable allows you to add an aftermarket rear view camera to the 5 inch factory radio screen on select Honda Civic, CR-V and Jazz models (2016 Onwards) car models.
The 32 Pin connector on this cable connects to the back of the factory Honda radio which upon reverse gear will display a rear camera image on the 5 inch screen.
Only suitable for Honda Civic (S/SE Models) CR-V (S-Models) and Jazz (S-Models) from 2017 Onwards.
PLEASE SEE PRODUCT IMAGES FOR COMPATIBLE RADIOS
This cable allows you to add an aftermarket back-up NTSC camera to various Lexus cars (2012 Onwards) with GEN7/GEN8/GEN9 Media-Navigation Systems.
PLEASE NOTE: Only suitable for 59 pin and 16 pin connection
ES series cars of 2012-2018 MY are not supported!
Plug and Play cable to add an NTSC reverse view camera to Renault and Nissan vehicles with EasyLink 8" head-units
Nissan Primastar 08/21 on , Renault Express Van, Kangoo, Master, Trafic Rapid 05/2021 onwards.
The camera input coding will need to be activated by a dealer if not already enabled at factory.
Reverse camera to RGB video input interface for VW cars with RNS315, RNS510 or RCD510 original head units.
Only for NTSC camera's. CODING NEEDED BY VW ENGINEER WITH DIAGNOSTIC TOOL
Adapter harness to add a reverse camera to an original Volkswagen radio screen.
This harness has a built in interface to give ignition power and a reverse feed to the camera.
Note, camera input function needs to be CODED to the car by a VW dealer or a specialist engineer with VCDS.
Rear view NTSC camera interface for Mercedes Benz Vito and Viano vehicles fitted with original Audio 15 head units.
Includes plug and play harness
Front and rear view camera and video input interface for various Land Rover models with GVIF technology/ touch screen navigation version 1 and 1.1. This interface allows for rear-view camera input and two additional video sources.
PLEASE NOTE: Only suitable for vehicles with factory navigation
THIS INTERFACE ONLY WORKS WITH NAVIGATION SWITCHED ON
Add an aftermarket front and/or rear view camera to the vehicles factory Navigation screen on select Buick LaCrosse and Regal car models with factory fitted CD500/ DVD800 systems.
PLEASE NOTE: Only suitable for vehicles with factory navigation switched on
Add an aftermarket front and/or rear view camera to the vehicles factory Navigation screen on select Vauxhall Astra J, Insignia A and Meriva B car models with factory fitted CD500/ DVD800 systems.
PLEASE NOTE: Only suitable for vehicles with factory navigation switched on
Add an aftermarket front and/or rear view camera to the vehicles factory Navigation screen on select Jaguar XF (X250) car models with factory fitted Version 1.1 touch-screen navigation
PLEASE NOTE: The vehicle must be in navigation map view in order to see the reverse camera
Rear view NTSC camera interface for Landrover Discovery 4 and Range Rover 2009-2012 with 2nd generation touch screen navigation
Also provides Video in Motion
Includes plug and play harness
Rear view camera interface for Landrover Discovery 4 (2012-2015) and Range Rover 2011-2015 with 3nd generation 8.2" touch screen navigation, and In Control Touch Pro
Also provides Video in Motion
Includes plug and play harness 16 pin Grey connector
Rear view camera interface for a single NTSC camera
Fo cars with 8" In Control Touch Pro screens. Only for model year 2015-06/2016
Includes plug and play harness QUADLOCK connector
Rear view camera interface for NTSC camera's.
Landrover, and Range Rover and Jaguar cars with 8" In Control Touch Pro screens. For model year late 2016 onwards
Includes plug and play harness QUADLOCK connector
Rear view camera input interface for BMW X5/X6 with CCC Navi or radio. Allows you to connect a rear-view camera to the CCC factory navigation system.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
Reverse Camera input adaptor for Ford Sync 2 8 inch & Sync 3 Systems. Vehicle Coding required
Enables connection of a aftermarket backup camera to the original OEM system.
Reverse Camera interface adaptor for factory Ford SYNC 2.5 / SYNC 3 systems (version 3.0 / 3.2 / 3.3) with 7 or 8 inch monitor screen and new 32-PIN Ford connector
This is a plug-and-play "T" Harness that allows you to easily add a back-up camera (when your vehicle did not come with a OEM backup camera) to select OEM systems while retaining factory settings.
Disconnect the factory connector and connect our T-Harness inline.
PLEASE NOTE: Coding is required with Forscan to enable RVC function on Sync systems
Rear view camera input interface for Chrysler, Dodge, Fiat, Lancia cars with Uconnect head units and seperate 8.4 inch monitors. Only compatible for cars with Uconnect 5 inch or 8.4/ RB5 and 8.4/ RE2 system monitors with 22 pin connector.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
Rear view camera interface for the activation of the factory rear view camera input. Compatible with Dodge,Jeep and Fiat cars with Uconnect 5 inch or 8.4 inch systems with 52 pin connection.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
PCB Insertion needed between the head-unit and the Monitor . NOT suitable for DIY users
PLEASE CHECK LONG DESCRIPTION NOTES FOR COMPATIBILITY
Extra PCB insertion required into original radio .
Only Suitable for Mini 6.5inch basic EVO BIS radio with all-in-one radio behind screen
the BIS radio has a 42 pin rectangular connector rather than the standard 40 pin that is in the EVO systems and NBT systems
PLEASE NOTE: not recommended for DIY . Experienced engineers only.
CAN BUS reverse switching is ONLY FOR VEHICLES WITH AUTOMATIC GEAR SHIFT
Suitable for Land Rover/ Jaguar models with factory fitted Bosch head units with 8 inch touch screen display. 2012 to 2015.
Jaguar F Type (13-15) Jaguar XF X250 (12-15) Jaguar XJ X351 (10-15)
Landrover Discovery4 L319 (12-14), Freelander 2 L359 (2013 only) Range Rover Vogue L322 ,Sport L320 (facelift) Evoque L358
This camera interface allows you to add an aftermarket camera to the original OEM head unit. Suitable for Land Rover/ Jaguar models with factory fitted Harmon head units with 8 inch display.
Add rear and front cameras to the OEM monitor of select Audi group cars with MMI 3G+ High
NOT suitable for MMI3G low/ basic
For Audi A6L/A7/A8L 2012-2016, VW Touareg 8" Navigation screen
Harness is fitted at the front behind the head-unit and in the rear boot area to the parking control module.
This interface allows you to add rear and front cameras to the OEM monitor of select Audi group cars with MIB2, Porsche cars with PCM 4.0 or PCM 4.1 and Volkswagen vehicles with composition Media or Discover Pro systems. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display. No special coding is needed as the interface integrates with the LVDS cable behind the vehicle head unit. The rear camera will activate as soon as reverse gear is engaged. The front camera will only activate if reverse gear is selected and then immediately afterwards drive forward gear is selected.
This interface allows you to add A front/ rear view camera to the OEM monitor of Audi car models with original MMI, MMI Nav +, 4G MMI and MIB2 audio systems. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
The adapter also has video inputs for external video sources connection such as an additional camera, DVD or Android TV boxes.
PLEASE NOTE: This interface requires hard wiring to the original head units main connector in order to generate the CANBUS. We recommend this be done by an experienced car audio technician
PLEASE CHECK THE COMPATIBLITY OF YOUR VEHICLE IN THE LONG DESCRIPTION
Add a rear camera to the OEM monitor of select Audi group cars with MMI 3G
Audi A1 Q3 with MMI 3G high or low
Audi A4 (B8) Audi A5/Q5 , A6 /Q7(years 2010-2012 only) with MMI3G high or 3G+
An LVDS cable is fitted at the front behind the head-unit and a cable harness to the CANbus gateway control module behind glove-box or under steering wheel.
This interface allows you to add rear and front backup and parking cameras to the OEM monitor of an Audi car with MMI 3G or 3G+
It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
PLEASE NOTE: This interface requires hard wiring to the Audi's climate control module in order to generate the CANBUS. Locations and connections can vary depending on the car model. Please refer to installation instructions for more info.
This interface allows you to add a rear and front camera to the OEM monitor of an Audi car without a MMI system. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
This interface allows you to add a rear and front camera to the OEM monitor of a Mercedes car with original NTG5 audio system. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
This interface allows you to add a rear and front camera to the OEM monitor of a Mercedes car with Command APS NTG 4.5. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
This camera interface allows you to add a rear and/or front camera to the OEM monitor of a Mercedes car with original NTG5.5 audio system. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
Only suitable for Mercedes cars with original NTG 5.5 audio systems with either a 10.2 or 12.3 inch monitor
This interface allows you to add a rear and front camera to the OEM monitor of a 2014 to 2017 onward Volvo car with Sensus technology.
ONLY FOR CARS WITH NAVIGATION AND GLOBE SYMBOL ON RADIO
It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
This interface allows you to add a rear and front camera to the OEM monitor of Peugeot and Citroen cars with SMEG navigation screens.
It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
ONLY SUITABLE FOR 2016 Onwards models with RLINK 2
Captur, Clio 2017- 2019, Espace 2016- 2020, Kadjar, Koleos 2016 >,
Master, Megane, Talisman 2016- 2020,Scenic from 10/2016,
PLEASE CHECK LONG DESCRIPTION NOTES
Add a rear parking camera to the Original screen on select Peugeot, Citroen, DS, Toyota and Opel/ Vauxhall vehicle models with a 7 or 8 inch NAC High or Low navigation Touch screen monitor.
This interface allows you to connect a reverse camera to the original factory fitted touch screen and display a rear view camera image upon putting the vehicle into reverse gear.
Please note: This interface is designed for select Peugeot, Citroen, DS, Toyota and Opel/ Vauxhall vehicle models with a 7 or 8 inch NAC Touch screen
Add a rear parking camera to the Original screen on select Peugeot and Citroen cars with NAC high or low navigation Touch screen monitors. Adds active parking lines and integrates with the cars parking sensors to provide a visual parking display. Has optional Front camera or DVR input.
Please note: This interface is designed for Citroen/ Peugeot vehicles with a 9 ,10 or 12 inch NAC Touch screen
For 7 or 8 Inch NAC touch Screen, please use 27-563
Compatible with Vauxhall , Opel, Chevrolet and Buik CD500, DVD600/800/900, CD600 Intellilink and DVD950 Intellilink infotainment systems.
Atra J, GTc, Insignia A, MerivaB, Mokka A and other vehicles model year 2012-2013
Front and rear view camera and video input interface.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
Rear view camera and video input interface for Vauxhall/Opel models with R4.0 IntelliLink system and 7" Monitor with Radio DIN-cage attached to it. (all in one units)
This NOT plug and play as a new PCB needs to be attached to the existing radio. Not for models with a separate screen away from the radio module.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
Rear view camera and video input interface for Vauxhall/Opel models with R4.0 IntelliLink system and 7" Monitor with separate radio module
Astra K (Sports Tourer and 5 door models) 2016-2019, Insignia B (2017-06/2018) Karl up to 03/2018, Chevrolet Camaro 2016 on.
Not suitable for models with all in one radio and monitor. Use item 27-565 for these.
PLEASE CHECK LONG DESCRIPTION NOTES
Rear view camera and video input interface suitable for various Alfa Romeo, Citroen, Dodge and Fiat vehicles with Uconnect 5 VP2/ RA2 with DIN housing behind the front panel and 5 inch monitor . This interface allows you to connect a rear-view camera and two additional video-sources to a factory-infotainment system.
PLEASE NOTE: Only Suitable for Uconnect 5 VP2/RA2 systems with CD-drive and DIN-shell behind front-panel
Suitable for MINI cars made between 2013 and 2016 with cars with NBT Navigation on a 6.5 or 8inch screen
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
This camera interface allows you to add a rear and/or front view camera to the existing OEM monitor. Suitable for BMW cars with NBT Navigation on a 6.5, 8.8 or 10.25 inch OEM monitor.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
Suitable for BMW , MINI cars with NBT2 EVO ID5/ID6 systems on a 6.5, 8.8 or 10.25 inch OEM monitor.
NB. Dynamic parking guidelines are not available for all vehicles. Factory PDC display may not work on all vehicles.
PLEASE SEE LONG DESCRIPTION
Rear-view camera input and video in motion interface for Porsche PCM3 and PCM3.1 navigation systems
Includes plug and play harness QUADLOCK connector
This interface allows you to add an aftermarket front and/or rear view camera to the factory infotainment system. Compatible with Porsche cars with PCM 3 and PCM 3.1 navigation systems.
This camera interface allows you to add a front and/or rear view camera to the existing OEM monitor. Suitable for select BMW cars with ID7/ MGU (Media Graphic Unit) iDrive systems on either a 10.2 or 12.3 inch screen.
PLEASE CHECK LONG DESCRIPTION FOR FURTHER DETAILS
This camera interface allows you to add a front and/or rear view camera to the existing OEM monitor.
Only suitable for Discovery 5 and Jaguar E Pace 2016 > with 10" single screen Harman systems (Touch Pro)
FITTED UNDERNEATH DRIVERS OR PASSENGER SEAT
PLEASE CHECK LONG DESCRIPTION FOR FURTHER DETAILS
This camera interface allows you to add a front and/or rear view camera to the existing OEM monitor. Suitable for Land Rover cars with dual screen systems (Touch Pro Duo)
PLEASE CHECK LONG DESCRIPTION FOR FURTHER DETAILS
Add camera (S) to OEM system on a select Mercedes vehicles (2019 Onwards) with MBUX NTG6 system with a 7 inch screen without satellite navigation
This interface can be used when adding front, rear and side view cameras to a 2019 onwards Mercedes with MBUX NTG6 such as Mercedes A-Class (W177), B-Class (W247), CLA-Coupe (C118), GLB (X247) and Sprinter(W907/910)
PLEASE NOTE: Only suitable for select Mercedes vehicles (2019 Onwards) with a 7 inch screen without satellite navigation and 31-pin connector
This interface allows you to add rear camera to the OEM monitor of select VW cars with MIB3. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
Connects at the head-unit control module beneath glove box
Suitable for select Ford vehicles 2018 on with 32 pin SQUARE CONNECTOR.
with Sync Connect 4inch or Sync 2.5 (Sync3 light /R5) Tablet version. 6.5/7/8 inch
Normally not for vehicles with Navigation ( these have Sync 3 full version)
PLEASE CHECK LONG DESCRIPTION FOR FURTHER DETAILS
Suitable for Actros 2018 and Arocs 2020 vehicles 10.25 inch Monitor 26 pin radio connector without Navigation.
The multimedia cockpit with 10.25inch monitor is available with and without navigation. With navigation always has the 31pin radio connector, without navigation has either the 31pin or a 26pin radio connector. For the version with 31pin radio connector, the interface with the item number 27-588 ( RL4-MBMC) is available including a 31pin plug & play harness.
PLEASE CHECK LONG DESCRIPTION FOR FURTHER DETAILS
Suitable for Actros 2018 and Arocs 2020 vehicles 10.25 inch Monitor 31 pin normally with Navigation.
The multimedia cockpit with 10.25inch monitor is available with and without navigation. With navigation always has the 31pin radio connector, without navigation has either the 31pin or a 26pin radio connector. For the version with 26pin radio connector, the interface with the item number 27-587 ( RL4-MBMRT) is available including a 26pin plug & play harness.
PLEASE CHECK LONG DESCRIPTION FOR FURTHER DETAILS
Video inserter for Vauxhall / Opel cars with Navi 900 Intellilink Systems ( Gen1 and 2) with 8 inch touch monitor or Chevrolet cars with MyLink IO6 infotainment
Insignia A (2014-2016) , Insignia B (20174-06/2018), Mokka X (2016-2020) Astra K (2016-2019)
This interface allows you to add a rear and front camera to the OEM monitor of a Mercedes A-Class with Command APS NTG 6 (7-inch screen)
This interface allows you to add a rear and front camera to the OEM monitor of a Mercedes A-Class with Command APS NTG 6 (10.25-inch screen)
This interface allows you to add rear and front backup and parking cameras to the OEM monitor of select Mercedes car models (WITH NTG 5.5/ NTG6 MBUX)
It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
PLEASE NOTE: This interface requires hard wiring to the original head units main connector in order to generate the CANBUS. We recommend this be done by an experienced car audio technician
Locations and connections can vary depending on the car model. Please refer to installation instructions for more info.
This interface allows you to add rear camera to the OEM monitor of select Audi cars with MIB3 multimedia
It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
Connects at the head-unit control module beneath glove box
Fits Audi A4/A5/Q5 (2021 facelift upwards) Audi A3 (2021 on), Audi Q3 (2022 on)
This interface allows you to add rear and front backup and parking cameras to the OEM monitor on Audi TT (2015 Onwards) car models.
It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
PLEASE NOTE: This interface requires hard wiring to the original head units main connector in order to generate the CANBUS. We recommend this be done by an experienced car audio technician
Please refer to installation instructions for more info.
Add front and /or rear camera to the original screen on Mercedes Sprinter vehicles 2018 onwards with MBUX NTG6 system with a 7 inch screen with Original navigation
Only suitable for Mercedes vehicles with a 7 inch screen with satellite navigation. The connector behind the radio is 26-pin
DOES NOT show original PDC ( Park distance control ) when camera is engaged
NOT SUITABLE FOR 10 inch screen systems
Add front and /or rear camera to the original screen on Mercedes Sprinter vehicles 2018 onwards with MBUX NTG6 system with a 7 inch screen without satellite navigation
Only suitable for Mercedes vehicles with a 7 inch screen without satellite navigation. The connector behind the radio is 31-pin
DOES NOT show original PDC ( Park distance control ) when camera is engaged
Video inserter for front and rear view camera for 7" Monitor or 9.3inch Tablet
Not suitable for models with 7inch Tablet or for models with Easylink all in one units with Din cage behind the Monitor.
Captur, Clio V ,Espace 2020 >, Megane Twingo 2021 on,
PLEASE CHECK LONG DESCRIPTION NOTES
Smartphone/ Camera integration for Audi A6/A7 (2012-2015) with MMI 3G+ Systems (WITH OEM 6.5 INCH SCREEN DISPLAY)
For later facelift models (2016-2018) with MMI 4G+ systems, please use 27-837
PLEASE NOTE: PLEASE READ LONG DESCRIPTION AND INSTRUCTIONS BEFORE PURCHASING!
Smartphone/ Camera integration for Audi A8 (2012-2017) with MMI High 3G System (7 INCH OEM screen)
PLEASE CHECK LONG DESCRIPTION
Smartphone/ Camera integration designed for Audi Q7 (2012-2015) with MMI 3G+ system (6.5 INCH OEM screen)
PLEASE CHECK LONG DESCRIPTION
Smartphone/ Camera integration designed for Audi A1 (2013-2018) car models with MMI 3G systems.
PLEASE NOTE: This interface requires inserting a PCB Board to the original screen and dismantling the original Audi Radio. This should only be carried out by professional car audio technicians!
PLEASE CHECK LONG DESCRIPTION
Smartphone/ Camera integration for Audi Q3 (2014-2018) car models with MMI 3G+ High Systems (7 INCH SCREEN WITH NAVI)
PLEASE NOTE: This interface installation should only be carried out by professional car audio technicians or an individual with relevant car audio experience
PLEASE READ LONG DESCRIPTION AND INSTRUCTIONS BEFORE PURCHASING!
Smartphone/ Camera integration for Peugeot and Citroen vehicles with SMEG/MRN navigation systems. Features include Carplay, Android Auto and screen mirroring.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
Smartphone/ Camera integration for Peugeot and Citroen vehicles from 2016 onwards with NAC high or low navigation Touch screen monitors. Features include Carplay, Android Auto and screen mirroring.
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
Wired Smartphone/ Camera integration designed for Audi cars with OEM MIB II systems with 7 or 8.3 inch screens. The car must have AUX in for this interface to work.
This interface is NOT wireless and needs the smartphone to be connected by USB
The original MIB 2 system consists of the MIB 2 main unit with either a 7/8.3 inch monitor with 4pin LVDS connector.
PLEASE CHECK LONG DESCRIPTION
AUDIO IS VIA THE CARS AUX IN SELECTION. The USB can be converted using 24-040 or AUX can be activated by a Mercedes specialist dealer
Smartphone/ Camera integration designed for Mercedes with NTG 4.5 and 4.7 OEM system 2012-2015
PLEASE CHECK LONG DESCRIPTION
PLEASE CHECK LONG DESCRIPTION FOR COMPATIBILITY NOTES
5 metre Single male to male Phono/RCA video extension cable
Cable colour: Black
Connection: 2 x male Phono plug
Length: 5 metres
10 metre Single male to male Phono/RCA video extension cable
Cable colour: Black
Connection: 2 x male Phono plug
Length: 10 metres
15 metre Single male to male Phono/RCA video extension cable
Cable colour: Black
Connection: 2 x male Phono plug
Length: 15 metres
Add a rear parking camera to the Original screen on select Volkswagen ID3 ID4 ID5 vehicle models with a 10 inch multimedia tablet MIB3 screen monitor.
The interface included in this kit allows you to add a rear camera to the OEM monitor of select VW cars with MIB3. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
This integration kit also comes complete with a UK & European car number plate/ registration plate frame with built in rear view camera, providing additional visual safety to the back of the vehicle, whilst maintaining its original appearance.
Add a rear parking camera to the Original screen on select Volkswagen T-Cross vehicle models with a Discover Media system.
The interface included in this kit allows you to add a rear camera to the OEM monitor on select Volkswagen T-Cross car models. It adds active parking lines and integrates with the cars parking sensors to provide a visual parking display.
This integration kit also comes complete with a tailgate handle camera which secures into the place of the original tailgate handle housing on the back of the vehicle and provides additional visual safety to the back of the vehicle, whilst still maintaining it's original appearance.
